Cisco CP-PWR-CORD-CE= — European AC Power Cord for Cisco IP Phone Power Cubes
C13 to CEE 7/72.5 mEuropeFor Power Cube 4
The Cisco CP-PWR-CORD-CE= is Cisco's European AC power cord with an IEC 60320 C13 connector and a CEE 7/7 (Schuko) plug, 2.5 m long, used to connect a Cisco IP Phone Power Cube to a European wall socket when the phone is not powered by PoE.
Cisco sells its IP phone power cubes without a mains cord and asks you to add the cord for your country. CP-PWR-CORD-CE= is the “Central Europe” option, the one that fits the Schuko-type sockets used in most of continental Europe; it is the part to order when a phone sits on a switch port without PoE.
Before you order: This is only the mains cord. On its own it does not power a phone: it needs the Cisco IP Phone Power Cube 4 (CP-PWR-CUBE-4=), which Cisco describes as a 48 V AC-to-DC supply for non-PoE deployments. Phones powered by a PoE switch do not need it at all.
What's in the Box
- 1 × Cisco European power cord, IEC C13 to CEE 7/7 (M), 2.5 m
What It Means in Practice
- Plug the C13 end into the Cisco Power Cube and the CEE 7/7 end into a wall socket or power strip.
- 2.5 m gives enough slack to reach a floor socket from a desk.
- The CEE 7/7 plug fits Schuko (type F) and French (type E) sockets.
- If you are moving phones onto a PoE switch, you can retire both the cube and the cord.
What Will Not Work
- UK sockets (BS 1363) — Cisco sells the -UK version; Swiss sockets need the -SW cord.
- Powering a phone without the Cisco Power Cube — the cord carries mains AC, not phone power.
- The newer Cisco 7800 Power Adapter 3, which uses interchangeable regional clips instead of a cord.
- Devices that need a C15 (hot-condition) or C5 (clover-leaf) inlet.
Technical Specifications
| Identification |
| Part Number |
CP-PWR-CORD-CE= |
| EAN / GTIN |
0746320318714 |
| Brand |
Cisco |
| Cable |
| Type |
AC power cord |
| Connector A |
IEC 60320 C13 |
| Connector B |
CEE 7/7 (male, Schuko) |
| Length |
2.5 m |
| Region |
Europe (Central Europe) |
| Compatibility |
| Used with |
Cisco IP Phone Power Cube 4 (CP-PWR-CUBE-4=) |
| Phones (per distributor listing) |
Cisco IP Phone 7961G, 7961G-GE, IP Phone 7900 series |
| Warranty |
| Warranty |
1-Year Warranty (Singular) |
| Manufacturer Term |
Not published separately by Cisco — claims handled through Singular |
Frequently Asked Questions
Do I need this if my switch has PoE?
No. PoE phones get power from the switch; the cord is only for the Power Cube used in non-PoE installations.
Will any C13 kettle-type cord work?
Electrically a standard C13 cord fits the cube, but this is the Cisco-listed part for Europe if you want genuine Cisco accessories.
Is it suitable for the UK or Cyprus 3-pin sockets?
No — this cord has a CEE 7/7 plug. For BS 1363 sockets use the Cisco -UK cord, or ask us.
Singular Expert Insight · Buyer's Guide
Most Cisco desk phones today run on PoE, so a mains cord and power cube are only needed where the switch port has no PoE. Before buying a cube and cord for every phone, check whether a
PoE switch would be simpler — one cable per desk instead of two.
✓ Buy it if you power Cisco IP phones from a Power Cube 4 and need the European mains cord.
✕ Skip it if your phones run on PoE, or your sockets are UK-type (BS 1363).
→ Also consider a PoE switch to remove the need for cubes and cords.
Not sure whether your phones need a cube and cord? Send us your phone and switch models and we will check before you order.